Simple XL PVA dropper designed to keep your PVA bags off the standard door flaps and away from the water to keep them dry whilst being driven out in the boat.
Unfortunately the Actor PLUS standard hopper doors can let a small amount of water pass through them during driving, this can melt your bag on the way to your spot and stop you delivering your PVA bag as intended.
We’ve designed this XL Low profile PVA dropper to be a cheap cost effective way of keeping your bags dry from the underneath.
Can be used with the original Boatman Hopper cover to provide overall cover.
This XL Version is 50mm (2”) longer than the original and can support extra long PVA bags, with a maximum length of 145mm (5.7”) x 60mm (2.4”) in diameter (finished bags measured).
The PVA Dropper consists of the following parts :
Main body, this is just drop into the hull and has been perfectly matched to the Hull design of the Actor PLUS - and as you would expect fit’s like a glove.
It also incorporates a cut-out to guide the line through to the rear of the hopper doors.
Bombay Doors / Flaps, these have been specially designed to have a perfect rounded contact point with the original hopper doors, this minimises friction and allows the flaps to be shut as the original doors are shut - so no messing around holding the flaps out the way or having to remove the system and reset every time.
Pivoting Bushes / Screws, we utilised the same technology from the Vulcan Rear mount to ensure screws could be fully tightened without “pinching” the body together - this give a nice resistance free loose design without the fear of it coming unattached. To do this we utilise plastic bushes with plastic welded inserts into the flaps.
Instructions to use :-
Open the hopper doors, insert the PVA dropper.
Place PVA bag through the dropper,
Close one of the hopper doors,
Ensure your line is passing through the cutout in the pva dropper and wont get trapped when closing the second door, then close the remaining door,
Send it out !
When putting out the second rod, please ensure to dry any water from the flaps before placing a bag on it !
Manufactured from the highest quality 3D printed filament - will not fade or distort in sunlight
Will be supplied already fully assembled ready to use.
Main body will be black, optional coloured flaps (made from outdoor grade PETG) please see the colour chart picture and make your selection when ordering.
Simple XL PVA dropper designed to keep your PVA bags off the standard door flaps and away from the water to keep them dry whilst being driven out in the boat.
Unfortunately the Actor PLUS standard hopper doors can let a small amount of water pass through them during driving, this can melt your bag on the way to your spot and stop you delivering your PVA bag as intended.
We’ve designed this XL Low profile PVA dropper to be a cheap cost effective way of keeping your bags dry from the underneath.
Can be used with the original Boatman Hopper cover to provide overall cover.
This XL Version is 50mm (2”) longer than the original and can support extra long PVA bags, with a maximum length of 145mm (5.7”) x 60mm (2.4”) in diameter (finished bags measured).
The PVA Dropper consists of the following parts :
Main body, this is just drop into the hull and has been perfectly matched to the Hull design of the Actor PLUS - and as you would expect fit’s like a glove.
It also incorporates a cut-out to guide the line through to the rear of the hopper doors.
Bombay Doors / Flaps, these have been specially designed to have a perfect rounded contact point with the original hopper doors, this minimises friction and allows the flaps to be shut as the original doors are shut - so no messing around holding the flaps out the way or having to remove the system and reset every time.
Pivoting Bushes / Screws, we utilised the same technology from the Vulcan Rear mount to ensure screws could be fully tightened without “pinching” the body together - this give a nice resistance free loose design without the fear of it coming unattached. To do this we utilise plastic bushes with plastic welded inserts into the flaps.
Instructions to use :-
Open the hopper doors, insert the PVA dropper.
Place PVA bag through the dropper,
Close one of the hopper doors,
Ensure your line is passing through the cutout in the pva dropper and wont get trapped when closing the second door, then close the remaining door,
Send it out !
When putting out the second rod, please ensure to dry any water from the flaps before placing a bag on it !
Manufactured from the highest quality 3D printed filament - will not fade or distort in sunlight
Will be supplied already fully assembled ready to use.
Main body will be black, optional coloured flaps (made from outdoor grade PETG) please see the colour chart picture and make your selection when ordering.
